How to Install a Ceiling Fan Where No Fixture Exists (Experts Guide)

Rate this post

A ceiling fan is one thing you don’t just know how useful it is until you have it. You want them in every room of your house when you know this. You’ve already got a ceiling light fixture if you want to install it in a bed. It’s a cot.

Willing to Buy the Best ceiling fans with bright lights? But there are no fixtures in the desired room?

It would help if you mounted it yourself with some expertise. You must determine where you want to place the fan brace and electric box, locate the power supply, take the cables to the ventilator position, switch and attach all the wires.

It sounds like many things to do, but it can be very straightforward if you have any easy experience. There is also a way to mount a ceiling ventilator where there is no attachment.

How much does it cost to install a ceiling fan where there are no fixtures?

If you are willing to do it yourself, installing a ceiling fan can be very cheap. Let’s, therefore, make a fast bill of materials. Let’s assume you already purchased a fan that we can remove from the estimate to exclude it. At Home Depot, we use the rates.

You will find quality braces for only $20 or up to $150, with electric metal boxes. You can need approximately 15 feet of wire, maybe up to 20 feet according to the width of your bedroom. It is recommended to buy packages of 25 feet, which are around $25 for 14 sizes and $35 for 12 sizes.

Quality wall boxes for 2-gang units vary from $3 or for 3-gang units from $4. The pricing of fan control switches is up to $100 for Wi-Fi activated switches of excellent quality with a 3-step fan and an on/off light switch. Check out our ceiling fan control switch recommendations here.

If I add up these numbers, we can see that you can only mount the fan yourself from a timid $70 to almost $300, but add another $50 to $70 if you need an electrician to assist.

Stepwise guide to install a ceiling fan where no fixture exists

Select The Location

Certainly, the dead center of the ceiling is the ideal place for a ceiling fan. But maybe it isn’t the best. Your ceilings have the construction of parallel slidings right behind the rock sheets, whether they are a duvet or another story above the bed.

You would have to cut a hole in the sheet so that you can cut them carefully. Since these joists are a carrying feature, they give you the place to attach the fan bracelet on the ceiling that carries the fan weight.

How large a hole you need is determined by the structure of your particular brace and electric box. Most braces come with a package, so there is no problem with compatibility. The easiest way to cut the hole between two joints is in the middle, and it is even easier to mark the cut. Place the electric box on the roof with a slip.

Find The Power Source

A deck fan requires a certain amount of power to power, so you need to find a particular power source to communicate with it. You are in a great position if your room has a wall switch. Depending on the fan style you choose to use, you will need to extend it to a two or 3-gang box from a 1-gang transfer box.

You should make sure that the breaker rotates and checks whether the breaker is a 20 or 15 amps breaker before you start working with or around the live wires. It would help if you never touched or operate on live wires. To make it even more secure, you can use a voltage tester to test the wires or power outlet.

Run The Wires

If you have easy access to your dressing room or another floor above your room, this part can be very easy or challenging. In the best situation, with open grass, all you need is to carry the wire to the fishing tape or a similar homemade contraction from the power source and drag it into the hole you cut.

Absolute worst-case scenario: if the floor over the room is, you’re going to have to trim many holes in a board and pierce a hole between the switching wall and the fan’s position of the electrical box through each joist. In this situation, a physician should better seek assistance.

Somewhere between would be if you had the floor above, but the ceiling joists would be rushed to the wall where the switches are placed or you would not be able to reach the barn. Two more hole are required over the turn, both on the wall and in the ceiling, for easier fishing of the wiring, first up the wall and then over the ceiling.

Please note, if the breaker you run is 15 amps, 14 gauge wires would be required, but 12 gauge wires are needed for a 20 amp breaker.

Install The Brace And Electrical Box

In this stage the installation guidebook for the specific brace you are using should be consulted. The designs and installation techniques are many different.

This move also allows you to make the nervous mistake of buying a separate wrist and electric box. It’s best to buy them as a pack; you’ve got the certainty that mounting, screws, or lack of them won’t be difficult.

You have a tee (we know how tenting it is to try to sort it out)! You must obey the directions! The bracelet helps to dampen potential vibrations and also bears a weight of well over 20 lbs by the fan.

The bracelet must be attached correctly and securely to the jacks. You should also avoid using electrical plastic boxes, especially if your fan is heavier and has proper heavy metal boxes. This is needed for the brackets of the fan and thus the fun, so you need to make sure they are robust enough to carry the whole weight.

Install The Fan And Switches

The fan brackets will attach to the electric box and install the fan, depending on the brand and model. The mounting points on the box and bracket are standardized and can only be connected with the supplied torches.

You can pull it on the bracket if you’ve done to see if everything is tight and secure.

You can also follow the cable diagram in the instructions to link the wires to the ventilator carefully. You should employ an electrician or ask for advice if you don’t feel competent enough.

Connecting the switches is very straightforward when you grasp the critical parallel wiring concept and turn the hot wire. Switching the hot wire only requires the switch. You can technically turn the neutral cable, but this condition is unsafe when your fan is even turned off.

If you are not comfortable taking this move yourself, we strongly suggest getting the advice of an electrician.

Final Word

We have helped you hope to add a ceiling fan that does not have a holder.

If you have the right equipment (even better if you have access to an above-ground dressing room), it’s not the most complicated task. Still, caution should be taken when dealing with electricity and setting up a ceiling fan, so call an expert if you are unsure.

Check Out Today's Deals!

X
error: Content is protected !!